• HUATEC GROUP CORPORATION
    باب
    Astm E114-15 Inch Type 1018 Test Block Carbon Steel Mini Iiw 2
  • HUATEC GROUP CORPORATION
    ویلیام
    Astm E114-15 Inch Type 1018 Test Block Carbon Steel Mini Iiw 2
  • HUATEC GROUP CORPORATION
    تام
    Astm E114-15 Inch Type 1018 Test Block Carbon Steel Mini Iiw 2
  • HUATEC GROUP CORPORATION
    لئو
    Astm E114-15 Inch Type 1018 Test Block Carbon Steel Mini Iiw 2
تماس با شخص : Noah
شماره تلفن : +8613911115555
واتساپ : +8613910983110

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE

محل منبع پکن
نام تجاری HUATEC
گواهی ISO, CE, GOST
شماره مدل HFD UL
مقدار حداقل تعداد سفارش 1PCS
جزئیات بسته بندی بسته صادرات استاندارد
زمان تحویل 1-4 روز
شرایط پرداخت T/T، Paypal، وسترین یونیون
قابلیت ارائه 5000PCS در ماه

برای نمونه ها و کوپن های رایگان با من تماس بگیرید.

واتساپ:0086 18588475571

وی چت: 0086 18588475571

اسکایپ: sales10@aixton.com

اگر شما هر گونه نگرانی دارید، ما 24 ساعت کمک آنلاین ارائه می دهیم.

x
جزئیات محصول
محدوده فرکانس 12.5KHz تا 10MKHz مبدل تماسی اندازه عناصر مختلف
مبدل صورت محافظت شده با فیلم یا کفش دستگاهی که دارای دو عنصر است عنصر دوگانه
گوه کانتور AID CID AOD COD مواد پلاستیک، آلومینیوم، آلیاژ
برجسته کردن

ultrasonic flaw detectors,ultrasonic flaw detection,digital ultrasonic flaw detector

,

ultrasonic flaw detection

,

digital ultrasonic flaw detector

پیام بگذارید
توضیحات محصول

 

Ultrasonic ndt equipment Ultrasonic Inspection Equipment Probe Transducer Phased Array Prob

 

1. Straight probe: single crystal p-wave straight probe double crystal p-wave straight probe

 

2. The Angle probe: single crystal shear Angle probe a1 < aL < a Ⅱ, twin shear Angle probe

 

Single-crystal p-wave oblique probe aL

AL is a climbing wave probe near a1. The longitudinal wave transmitted along the surface of the workpiece has the advantages of fast speed, high energy, long wavelength, deeper detection depth than the surface wave, and the requirement for the surface finish of the workpiece is higher than that of the surface wave (frequency 2.5mhz wavelength about 2.4mm).

 

3. Probe with curvature: circumferential curvature, radial curvature.

 

The circumferential curvature probe is suitable for the detection of axial defects in seamless steel tubes, straight welded tubes, tubular forgings and axial workpieces. When the diameter of the workpiece is less than 2000mm, the circumferential curvature of the probe shall be ground to ensure good coupling.

 

Radial curvature probe is suitable for the detection of radial defects in seamless steel pipe, butt weld of steel pipe, barrel forging, shaft workpiece, etc. When the workpiece diameter is less than 600mm, the radial curvature of the probe should be ground to ensure good coupling.

 

4. Focusing probe: point focusing line focusing.

 

5. Surface wave probe :(when the incident Angle of the longitudinal wave is greater than or equal to the second critical Angle, the transverse wave refraction Angle is equal to 90 to form a surface wave).

 

The transverse wave transmitted along the workpiece surface has a slow speed, low energy and short wavelength, and the detection depth is shallower than the crawling wave. Therefore, the requirements for the surface finish of the workpiece are stricter than the crawling wave.

 

Surface wave detection can only detect defects at a depth of two wavelengths from the surface of the workpiece. (frequency 2.5mhz wavelength about 1.3mm).

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 0

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 1

 

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 2

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 3

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 4

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 5

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 6

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 7

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 8

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 9Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 10

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 11

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 12

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 13

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 14

Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE 15